![]() #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLERĪfter build then upload of your firmware to your printers Arduino or mainboard as specified in the firmware documentation.īy default Marlin will use the U8G/DOGM libraries to handle the Smart Controller and assume that the LCD driver is the ST7920. Remove the comment characters "//", so the line now reads: #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLERĢ. Open the "Configuration.h” file and find the following line: For more details check Marlin's page on how to configure the firmware, see the LCD section.ġ. The basic requirement to add support in the Marlin Firmware is to enable the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER in the "Configuration.h”. Pictures of a Full Graphic Smart Controller made by RepRapDiscount Full Graphic Smart Controller Gerber FilesĪs firmware we used Marlins' sources, to update the firmware in the future you just need an Arduino board, so you are good to go ) RepRapDiscount Full Graphic Smart Controller Schematics The following figure shows the pinout mapping to an Arduino Mega 2560:Ĭlones and other manufactures may provide different connections, in particular models without SD-Card or models supporting only the SPI/Serial interface (most common) When used with a RAMPS board the "Smart Adapter" provides an easy connection with the RAMPS. The following figure shows the pinout mapping to an Arduino Mega 2560: The board has two 10-pin (2 row with 2.54mm pitch) box connectors marked EXP1 and EXP2 (10-PIN IDC CONNECTOR). The more common and generic boards use some flavor of a 12864 LCD with the ST7920, this is the case with most boards you find in online stores. ![]() Boards using a DOG-M128 Display use a ST7565 IC Driver. Some budget clones may have issues due to timing constraints with the display used.ĭepending on the vendor you may find boards using an ST7920 IC Driver, a ST7565 IC Driver, or other. Variants of the design may have fans or remove the SD-Card, among other changes. Many clones or variants only support the serial (SPI) interface. ![]() ![]() The original design supports the 8bit Parallel interface and a 4bit serial interface. This display board is supported by the most popular 3D Printer firmwares, yet differences in the LCD Drivers used and others may dictate the level of support in a given 3D printer mainboard and firmware combination. The preference of serial is mainly due to the use of the ( ) that implements the graphic support in these firmwares. The original design supports the 8bit Parallel display interface and a 4bit serial display interface, yet all of the common E3 Printer firmwares only support the 4bit Serial interface which only uses one pin for data, freeing more pins for other uses. The more common and generic boards use some flavor of a 12864 LCD with the ST7920, this is the case with most board you find in online stores. The Full Graphic Smart Controller comes with a 12864 (128圆4) LCD.ĭepending on the vendor you may find boards using an ST7920 IC Driver or a ST7565 IC Driver. When using a RAMPS board the Full Graphic Smart Controller is simple to connect using the "smart adapter" which connects directly to an Arduino Mega 2560. Given that many of the 3D printer's mainboards are based on the RAMPS design this display board is supported by many other mainboards. This display board is intended to provide an easy and simple solution to interact with a 3D printer. The RepRapDiscount_Smart_Controller is a similar design with a 20x4 character based display. This Full Graphic Smart Controller contains a SD-Card reader, a rotary encoder and a 128 x 64 dot matrix LCD display. 1.5 Support in Marlin Firmware V1 (new)īased on bkubicek idea and STB's DOGM128 implementation, we realized this full graphic smart controller.1.4 Pictures of a Full Graphic Smart Controller made by.1.1.1 Original Design and Clones/Variants.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |